Sonoma County Roofing Contractor

Roof & Gutter Busters, Inc. is a family-owned roofing and sheet metal contractor based in Rohnert Park, serving all of Sonoma County. We have installed gutters here since 2006 and have provided full roofing services since 2014. California license #988438, classifications C-39 Roofing and C-43 Sheet Metal. Owner Everardo Zuniga is personally on every job site.

When a Class A roof is required in unincorporated Sonoma County Decision diagram: if more than 50 percent of a roof area is re-roofed in unincorporated Sonoma County, a Class A assembly is required under Permit Sonoma Technical Bulletin B-07. Chapter 7A adds requirements in Very High Fire Hazard Severity Zones regardless. When does a Class A roof become mandatory? Unincorporated Sonoma County · Permit Sonoma Technical Bulletin B-07 You are re-roofing an existing structure in unincorporated Sonoma County Is more than 50% of the roof area being re-roofed? measured by area, not by cost or by slope NO YES 50% rule not triggered The Class A requirement under B-07 does not apply to this scope of work CLASS A ASSEMBLY REQUIRED Tested to ASTM E 108 or UL 790. The whole system, not just the shingle. Applies either way — Very High Fire Hazard Severity Zones In a State Responsibility Area, California Building Code Chapter 7A adds requirements on top of the above, including requirements reaching roof decks. CAL FIRE updated Sonoma County's hazard maps on February 24, 2025. Sonoma County Code §7-13 · California Building Code §1505.1 and §1505.2 · Permit Sonoma Technical Bulletin B-07 Incorporated cities run their own building departments and may differ. Confirm current requirements for your address.
When a Class A roof assembly is required for a re-roof in unincorporated Sonoma County.

Roofing in Sonoma County is not the same job it is elsewhere in California. Our winters are wet, our summers are dry and hot, much of the county sits in a designated fire hazard zone, and the rules that govern your roof change depending on which side of a city limit line your house sits on. This page explains what actually applies here, and what we do about it.

Roofing requirements in Sonoma County

Most homeowners we meet do not know these rules exist until a permit is pulled. They are worth understanding before you get estimates, because a bid that ignores them is not a real bid.

The 50 percent rule: when a Class A roof becomes mandatory

In unincorporated Sonoma County, if more than 50 percent of your roof area is re-roofed, the new roof must be a Class A assembly. This comes from Permit Sonoma Technical Bulletin B-07, which applies Sonoma County Code Section 7-13 and California Building Code Sections 1505.1 and 1505.2.

Class A is the highest fire-resistance rating for a roof covering, tested under ASTM E 108 or UL 790. The requirement is triggered three ways: new structures, any existing structure where more than half the roof area is re-roofed, and additions that create a new floor where any single floor exceeds 640 square feet.

Two practical consequences. First, a partial repair and a half-roof replacement are governed differently, and the line between them is 50 percent of roof area. Second, "Class A" describes the whole assembly, not just the shingle. Composition shingles have to be installed as part of a listed Class A system, with the installation method documented in the manufacturer's product literature. Buying a Class A shingle and installing it outside its listing does not produce a Class A roof.

Sonoma County is stricter than the state on wood shakes

This one surprises people who have read the state code. The California Building Code permits fire-retardant-treated wood shakes on single-family dwellings. Sonoma County does not accept that on its own. Under B-07, fire-retardant wood shakes must be tested and listed as part of a Class A system to be approved here.

If you have an existing shake roof in the county and you are planning to replace in kind, this is the first thing to resolve. We can tell you on an inspection whether the system you are considering will pass.

Which materials count as Class A

MaterialStatus in Sonoma County
Slate, clay or concrete tile, metalTreated as Class A when installed per manufacturer instructions
Composition / asphalt shingleMust be part of a listed Class A system; installation method must follow product literature
Built-up roofingMust be part of a listed Class A system
Fire-retardant wood shakeMust be tested and listed as a Class A system — stricter than the state code
Roof decks used as walking surfacesRequire Class A roofing, which may be installed over flammable decking such as redwood

There are narrow exceptions in the bulletin for greenhouses, glass or plastic patio covers attached to a single-family dwelling, residential car and boat covers, awnings, and State Fire Marshal–certified fabric membrane structures. Unconventional roofs are reviewed case by case.

Wildland Urban Interface and the 2025 fire hazard maps

In State Responsibility Areas, California Building Code Chapter 7A adds requirements on top of the Class A rule, including requirements that reach roof decks.

This matters more than it did a few years ago. CAL FIRE released updated Fire Hazard Severity Zone maps for Sonoma County on February 24, 2025, covering Very High Fire Hazard Severity Zones in both State Responsibility Area and Local Responsibility Area land. The maps become official 120 days after release, and local governments must adopt them where changes affect LRA Very High zones. Sonoma County's Fire Safety Ordinance #6396, adopted in 2022, carries development regulations tied to those zones.

The short version for a homeowner: your parcel's hazard designation may have changed recently, and it affects what you are allowed to put on your roof. Before you plan a replacement, check your current designation. Permit Sonoma's Fire Prevention Division can confirm it at (707) 565-2361.

Title 24 cool roofs: what actually applies in Santa Rosa and Rohnert Park

Cool roof requirements get quoted at Sonoma County homeowners constantly, usually incorrectly. Here is the accurate position.

Santa Rosa is the representative city for California Title 24 Climate Zone 2, which covers this part of Sonoma County. For single-family homes in Climate Zone 2, Title 24 Part 6 sets no cool roof requirement — not for new construction and not for re-roofing, on either low-slope or steep-slope roofs. Those mandates apply to other climate zones.

Where it does apply here is multifamily. For a multifamily low-slope roof alteration in Climate Zone 2, the requirement is 0.63 aged solar reflectance, 0.75 thermal emittance, and SRI 75, triggered when more than 50 percent of the roof area or more than 2,000 square feet is altered, whichever is less. Insulation at the roof deck, building-integrated solar coverage, and assemblies weighing at least 25 pounds per square foot can satisfy or exempt the requirement.

One statewide rule does apply to everyone: roofing products must carry a label or CRRC rating. If a product is not certified, the energy code assumes an aged solar reflectance and thermal emittance of 0.08/0.75 for asphalt shingles and 0.10/0.75 for other products — which can matter if your project is using a performance calculation.

If a contractor tells you a cool roof is legally required on your single-family home in Santa Rosa or Rohnert Park, ask them which code section. There may be good reasons to choose a reflective roof here. A Title 24 mandate is not one of them.

Permits and inspections

Re-roofing in unincorporated Sonoma County goes through Permit Sonoma. A few things are worth knowing before you apply:

  • Who can pull the permit. The property owner, or a contractor holding a C-39 license. We hold C-39 and pull the permit as part of the job.
  • Open violations block you. Any open building code violation on the property has to be resolved before a reroofing permit is issued.
  • At least two inspections. A pre-inspection (code 137) and a final inspection (code 199). Both should be scheduled before work starts.
  • Owner-builders need Form CSS-026.
  • Trust-owned property requires trust paperwork; HOA common areas and condominium exteriors require signed HOA authorization.
  • Coastal properties require a consultation with the Planning division first — relevant along the west county coast.
  • Material quantity is stated in squares (one square = 100 square feet).

Incorporated cities — Santa Rosa, Petaluma, Rohnert Park, Sebastopol, Healdsburg, Sonoma, Cloverdale, Cotati and Windsor — run their own building departments, and their requirements can differ from the county's. We handle permitting in the jurisdiction your property actually sits in.

Sources: Permit Sonoma Technical Bulletin B-07, Class A Roof Requirements · Permit Sonoma, Residential Reroofing · Permit Sonoma, CAL FIRE Fire Hazard Severity Maps · Cool Roof Rating Council, 2022 Title 24 Part 6 summary

Our Sonoma County roofing services

Residential roofing

Complete roof replacement, reroofing and re-covering, leak repair, roof sealing and roof inspections. We work in asphalt and composition shingle, metal, wood shake, and flat and TPO membrane systems. Every replacement is installed as a listed Class A assembly where the county or city requires one.

IMAGE 2 — residential roof replacement in progress
Suggested alt: "Roof replacement crew installing architectural shingles on a Sonoma County home"

Commercial roofing

Flat and low-slope commercial systems including TPO membrane, roof coatings and sealing, along with repair and maintenance for property managers and commercial owners across the county. If your building is multifamily and you are altering more than half the roof, the Title 24 cool roof threshold above is the first thing we check.

Seamless gutters and sheet metal

This is where the company started in 2006. We fabricate and install seamless aluminum, steel and copper gutters, downspouts and gutter guards, and we repair existing systems. We hold a C-43 Sheet Metal classification alongside the roofing license, which is not common among roofing contractors and is the reason our gutter work is fabricated rather than assembled from stock lengths.

IMAGE 3 — seamless gutter installation
Suggested alt: "Seamless aluminum gutter installation on a Sonoma County home"

Roof moss removal

Sonoma County's rain season runs roughly from late October into April, and on north-facing slopes and under tree cover that is enough to grow moss that lifts shingle edges and holds water against the roof.

We remove moss with soft-tool methods and treatment — not pressure washing. Pressure washing a composition shingle roof strips the granules that protect the asphalt and shortens the life of the roof, sometimes dramatically. It looks clean the day it is done and costs you years. Gutters are cleared as part of the service.

Skylights

Skylight installation and replacement, including flashing and the surrounding roof work, which is where most skylight leaks actually originate.

Roofs we see across Sonoma County

The county's building stock varies enough that the right answer changes by area:

  • Post-war and mid-century tract housing in Rohnert Park, Cotati and south Santa Rosa — mostly composition shingle on simple gable and hip roofs, often on their second or third replacement, frequently with original sheathing worth inspecting.
  • Rebuild-era homes in the areas affected by the 2017 fires — newer assemblies built to the fire codes in force at the time, where matching the existing listed system matters.
  • Older homes in Petaluma, Healdsburg and the town of Sonoma — steeper pitches, more complex rooflines, and more tile and shake, where a replacement has to respect the original roof's geometry.
  • Rural and hillside property in the Mayacamas and the west county — most likely to sit in a Very High Fire Hazard Severity Zone and most affected by Chapter 7A.
  • Agricultural and winery outbuildings — metal and low-slope membrane, often large spans with their own drainage problems.
IMAGE 4 — before/after or a tile or metal roof
Suggested alt: "Tile roof repair on an older home in Sonoma County"

Where we work

We serve all of Sonoma County, plus Napa and Marin counties, from our office in Rohnert Park.

We also serve Napa, Novato and San Rafael, and the surrounding Napa and Marin communities. Towns without their own page are served exactly the same way — call and ask.

Licensing, certification and warranty

ItemDetail
California license#988438 — C-39 Roofing, C-43 Sheet Metal
Manufacturer certificationGAF Certified contractor
Workmanship warranty20 years on our labor, separate from any manufacturer material warranty
InsuranceLicensed and insured; insurance claims welcome
In businessGutters since 2006, roofing since 2014
OwnershipFamily owned and operated — Everardo and Yoli Zuniga
LanguagesEnglish and Spanish — se habla español

A note on warranties, because they are routinely conflated. A material warranty comes from the shingle manufacturer and covers the product. A workmanship warranty comes from the contractor and covers the installation. Most roof failures are installation failures, which is why our 20-year workmanship warranty is the one worth reading. You can verify any California contractor's license, including ours, at the Contractors State License Board.

Free roof inspection and estimate, anywhere in Sonoma County

(707) 584-3010

Roof & Gutter Busters, Inc. — 6050 Commerce Blvd, Suite 200, Rohnert Park, CA 94928

Sonoma County roofing questions

Do I need a Class A roof on my house?

In unincorporated Sonoma County, yes, if more than 50 percent of your roof area is being re-roofed. Incorporated cities set their own requirements. We confirm which jurisdiction and which rule applies to your address before quoting.

Is a cool roof required on my home?

For a single-family home in Climate Zone 2, which covers the Santa Rosa and Rohnert Park area, Title 24 Part 6 does not require a cool roof for new construction or re-roofing. Multifamily low-slope alterations in Zone 2 do carry a requirement of 0.63 aged solar reflectance, 0.75 thermal emittance and SRI 75.

Can I install a new roof over my existing one?

Sometimes, depending on the existing layers, the condition of the sheathing and the requirements of the jurisdiction. Whether more than 50 percent of the roof is involved also determines whether the Class A requirement is triggered. We inspect the deck before recommending a re-cover over a tear-off, because a re-cover over failing sheathing buys a few years and costs more in the end.

How many inspections does a reroof need?

At least two in unincorporated Sonoma County — a pre-inspection, code 137, and a final inspection, code 199. We schedule both.

My property is in a Very High Fire Hazard Severity Zone. What changes?

Chapter 7A of the California Building Code adds requirements beyond the Class A rule, including requirements affecting roof decks. CAL FIRE updated Sonoma County's hazard maps in February 2025, so your designation may have changed since your last roof. We check the current designation as part of the inspection.

Should I pressure wash the moss off my roof?

No. Pressure washing strips the protective granules from composition shingles and shortens the life of the roof. Soft-tool removal and treatment achieves the same result without damaging the shingle surface.

Do you work with insurance claims?

Yes. Storm and fire-related claims are common here, and we are happy to work with your adjuster.

How long does a roof replacement take?

Most single-family replacements in this county are a multi-day job, with the exact duration depending on size, pitch, complexity and whether sheathing needs replacing. We give you a schedule with the estimate rather than after the contract.

IMAGE 5 — team photo or truck
Suggested alt: "Roof & Gutter Busters team in Rohnert Park, Sonoma County"

Roof & Gutter Busters, Inc.
6050 Commerce Blvd, Suite 200, Rohnert Park, CA 94928
(707) 584-3010 · CA License #988438 (C-39 Roofing, C-43 Sheet Metal)
Family owned and operated. Serving Sonoma, Napa and Marin counties. Se habla español.

Code and permitting information on this page is summarized from Permit Sonoma and Cool Roof Rating Council publications and is provided for general guidance. Requirements change and vary by jurisdiction — confirm current requirements for your address with your local building department before starting work.